Home | About us | Our Products | Contact us | Send Enquiry

        Our Products
Home Our Products Page 1 2

Deburring Tools

  • Used for general purpose
  • Countersinks
  • Chamfering
  • Deburing.
Size Small Dia Large Dia Cat no
mm mm  
0 Double End 2 5 CS-407
1 single End 5 10 CS-408
2 single End 10 15 CS-409
3 single End 15 20 CS-410
4 single End 20 25 CS-411
Note : Available in 820 and 900

Tool Holders


Turning Tool Holder(Adjsutable)
  • Machined Tool Holders
  • Supplied without Tool Bits.
Straight Cat No. Capacity Overall Length
inch mm inch mm
THAJ-139 3/16 to 1/4 5  to 6 5 127
THAJ-140 1/4 to 5/16 6  to 8 5-1/2 140
THAJ-141 5/16 to 3/8 8  to 10 6 152
THAJ-142 3/8 to 1/2 10  to 12 8 203

Turning Tool Holder (American Type)

  • Accurately Machined
  • Heat Treated and Hardened
  • Provided with one Wrench
  • Available in Straight, Left and Right Hand Shanks
  • Supplied with or without tool bits of Standard Length
Straight  Cat No. Left Hand  Cat No. Right Hand   Cat No. Holder Size BIT Size
Inch mm Inch mm
THA-101 THA-109 THA-117 5/16x3/4x 4-1/2 8 x 19 x 114 3/16 5
THA-102 THA-110 THA-118 3/8x7/8x 5 9.5 x 22 x 127 1/4 6
THA-103 THA-111 THA-119 1/2x1-1/8x 6 13 x 28 x 152 5/16 8
THA-104 THA-112 THA-120 5/8x1-3/8x 7 16 x 35 x 178 3/8 10
THA-105 THA-113 THA-121 3/4x1-5/8x 8 19 x 41 x 203 7/16 11
THA-106 THA-114 THA-122 7/8x1-3/4x 9 22 x 44 x 228 1/2 12
THA-107 THA-115 THA-123 1x2x11 25 x 50 x 280 5/8 16
THA-108 THA-116 THA-124 1-1/4x2- 1/4x 13 32 x 57 x 330 3/4 19


Knurling Tool Holders

  • Machined ground steel in Shiny black finish.
  • High Speed steel Knurls. Six Knurl Tool is provided with one pair each of fine medium and coarse Knurls.
  • Two Knurl Tool is provided with medium knurls, but other Knurls can also be provided if required.
  • Replacement Knurls are offerred as a complete spare set for Knurling tools.
Cat No. Tool Holder No. of Knurls Size of Holder
Inch mm
KT-209 2 5/16x3/4x5 8x19x127
KT-210 2 3/8x7/8x5-1/2 9.5x22x140
KT-211 2 1/2x1-1/8x6-1/2 12.7x28x165
KT-212 2 5/8x1-3/8x7-1/2 16x35x190
KT-213 6 5/16x3/4x5 8x19x127
KT-214 6 3/8x7/8x5-1/2 9.5x22x140
KT-215 6 1/2x1-1/8x6-1/2 12.7x28x165
KT-216 6 5/8x1-3/8x7-1/2 16x35x190
KT-217 6 1/2x7/8x6-1/2 12.7x22x165
KT-218 2 1/2x1/2x4-1/2 12.7x12.7x115
KT-219 2 1/2x1/2x5 12.7x12.7x127
KT-220 1 1/2x1/2x4 12.7x12.7x100
KT-221 1 3/4x3/4x5 19x19x127


Cutting Tools


Adjustable Hand Reamers

  • Each Reamer expands to the smallest size of next larger size.
  • Reamers are used for light cut, repair work, removing stock or simply for enlarging holes.
  • Reamers can be hand operated by use of wrenches. The size can be adjusted by moving the blades in tapered slots by means of loosening one nut and tightening the other.
Size   Range No. of Blades Cat No.  
Inch mm
8/A 1/4 to  9/32 6.35 to 7.14 4 AR-303
7/A  9/32 to 5/16 7.14 to 7.94 4 AR-304
6/A 5/16 to 11/32 7.94 to 8.73 4 AR-305
5/A 11/32 to 3/8 8.73 to 9.52 5 AR-306
4/A 3/8 to 13/32 9.52 to 10.32 6 AR-307
3/A 13/32 to 7/16 10.32 to 11.11 6 AR-308
2/A 7/16 to 15/32 11.11 to 11.91 6 AR-309
A 15/32 to 17/32 11.91 to 13.49 6 AR-310
B 17/32 to 19/32 13.49 to 15.08 6 AR-311
C 19/32 to 21/32 15.08 to 16.67 6 AR-312
D 21/32 to 23/32 16.67 to 18.26 6 AR-313
E 23/32 to 25/32 18.26 to 19.84 6 AR-314
F 25/32 to 27/32 19.84 to 21.43 6 AR-315
G 27/32 to 15/16 21.43 to 23.81 6 AR-316
H 15/16 to 1-1/16 23.81 to 26.99 6 AR-317
I 1-1/16 to 1-3/16 26.99 to 30.16 6 AR-318
J 1-3/16 to 1-11/32 30.16 to 34.13 6 AR-319
K 1-11/32 to 1-1/2 34.13 to 38.10 6 AR-320
L 1-1/2 to 1-13/16 38.10 to 46.04 6 AR-321
M 1-13/16 to 2-7/32 46.04 to 56.36 6 AR-322
N 2-7/32 to 2-3/4 56.36 to 69.85 6 AR-323
O 2-3/4 to 3-11/32 69.85 to 84.93 6 AR-324


Round Dies




Size Outer Dia.
of Dies		 Cat. No. For
Right Hand
Dies.		 Left Hand
Dies.
1/4” - 20 UNC 1” DH-562 DH-591
1/4” - 28 UNF 1” DH-563 DH-592
5/16” - 18 UNC 1” DH-564 DH-593
5/16” - 24 UNF 1” DH-565 DH-594
3/8” - 16 UNC 1” DH-566 DH-595
3/8” - 24 UNF 1” DH-567 DH-596
7/16” - 14 UNC 1-1/2” DH-568 DH-597
7/16” - 20 UNF 1-1/2” DH-569 DH-598
1/2” - 13 UNC 1-1/2” DH-570 DH-599
1/2” - 20 UNF 1-1/2” DH-571 DH-600
9/16” - 12 UNC 1-1/2” DH-572 DH-601
9/16” - 18 UNF 1-1/2” DH-573 DH-602
5/8” - 11 UNC 1-1/2” DH-574 DH-603
5/8” - 18 UNF 1-1/2” DH-575 DH-604
3/4” - 10 UNC 1-1/2” DH-576 DH-605
3/4” - 16 UNF 1-1/2” DH-577 DH-606
8” -   9 UNC 2” DH-578 DH-607
7/8” - 14 UNF 2” DH-579 DH-608
1” -  8 UNC 2” DH-580 DH-609
1” - 12 UNF 2” DH-581 DH-610
1” - 14 UNS 2” DH-582 DH-611
1-1/8” -  7 UNC 2-1/2” DH-583 DH-612
1-1/8” - 12 UNF 2-1/2” DH-584 DH-613
1-1/4” -  7 UNC 2-1/2” DH-585 DH-614
1-1/4” - 12 UNF 2-1/2” DH-586 DH-615
1-3/8” -   6 UNC 2-1/2” DH-587 DH-616
1-3/8” - 12 UNF 2-1/2” DH-588 DH-617
1-1/2” -   6 UNC 2-1/2” DH-589 DH-618
1-1/2” - 12 UNF 2-1/2” DH-590 DH-619
 


Carbon Tapes




Thread Size No. of Flutes Thread Length Overall Length Cat. NO
Plug Model Bottoming Model Taper Model Set of Three Plug, Bottom & Taper  Taps
1/4” -20 UNC 4 1” 2-1/2” TC-629 TC-657 TC-685 TC-685s
1/4” -28 UNF 4 1” 2-1/2” TC-630 TC-658 TC-686 TC-686s
5/16”-18 UNC 4 1-1/8” 2-23/32” TC-631 TC-659 TC-687 TC-687s
5/16”-24UNF 4 1-1/8” 2-23/32” TC-632 TC-660 TC-688 TC-688s
3/8” –16 UNC 4 1-1/4” 2-15/16” TC-633 TC-661 TC-689 TC-689s
3/8” –24 UNF 4 1-1/4” 2-15/16” TC-634 TC-662 TC-690 TC-690s
7/16”-14 UNC 4 1-7/16” 3-5/32” TC-635 TC-663 TC-691 TC-691s
7/16”-20 UNF 4 1-7/16” 3-5/32” TC-636 TC-664 TC-692 TC-692s
1/2”  -13 UNC 4 1-21/32” 3-3/8” TC-637 TC-665 TC-693 TC-693s
1/2”  -20 UNF 4 1-21/32” 3-3/8” TC-638 TC-666 TC-694 TC-694s
9/16”-12 UNC 4 1-21/32” 3-19/32” TC-639 TC-667 TC-695 TC-695s
9/16”-18 UNF 4 1-21/32” 3-19/32” TC-640 TC-668 TC-696 TC-696s
5/8”  -11 UNC 4 1-13/16” 3-13/16” TC-641 TC-669 TC-697 TC-697s
5/8”  -18 UNF 4 1-13/16” 3-13/16” TC-642 TC-670 TC-698 TC-698s
3/4”  -10 UNC 4 2” 4-1/4” TC-643 TC-671 TC-699 TC-699s
3/4”  -16 UNF 4 2” 4-1/4” TC-644 TC-672 TC-700 TC-700s
7/8”  - 9  UNC 4 2-7/32” 4-11/16” TC-645 TC-673 TC-701 TC-701s
7/8”  -14 UNF 4 2-7/32” 4-11/16” TC-646 TC-674 TC-702 TC-702s
1”    - 8  UNC 4 2-1/2” 5-1/8” TC-647 TC-675 TC-703 TC-703s
1”    -12  UNF 4 2-1/2” 5-1/8” TC-648 TC-676 TC-704 TC-704s
1-1/8”-7 UNC 4 2-9/16” 5-7/16” TC-649 TC-677 TC-705 TC-705s
1-1/8”-12UNF 4 2-9/16” 5-7/16” TC-650 TC-678 TC-706 TC-706s
1-1/4”-7 UNC 4 2-9/16” 5-3/4” TC-651 TC-679 TC-707 TC-707s
1-1/4”-12UNF 6 2-9/16” 5-3/4” TC-652 TC-680 TC-708 TC-708s
1-3/8”-6 UNC 4 3” 6-1/16” TC-653 TC-681 TC-709 TC-709s
1-3/8”-12UNF 6 3” 6-1/16” TC-654 TC-682 TC-710 TC-710s
1-1/2”- 6UNC 4 3” 6-3/8” TC-655 TC-683 TC-711 TC-711s
1-1/2”-12UNF 6 3” 6-3/8” TC-656 TC-684 TC-712 TC-712s

Magnetic Tools


Mabnetic Base – High Power

  • Made of fine quality Permanent Alnico Magnet.
  • Smooth easy ON/OFF switch.
  • Horizontal or Vertical positioning capability.
  • V-grooved base for mounting on cylindrical parts.
  • Accepts all AGD dial Indicators.
  • Magnetic Pull approx. 50-60 Kg. (110-130 lbs)


Cat No. Overall Height Base Dimension LXWXH
Inch mm Inch mm
MB-1090 9-1/4 235 1-7/8 x 1-3/4 x 2 48 x 45 x 50


Magnetic Vee Block




Cat No. Length Width Height Big V Small V
Inch mm Inch mm Inch mm Inch mm Inch mm
MB-1110 (Single) 2-3/4 70 2-1/8 54 2-7/8 73 1-1/2 38 3/4 19
MB-1111 (Single) 4 100 2-3/4 70 3-3/4 95 2 50 3/4 19
MB-1112 (Pair) 4 100 2-3/4 70 3-3/4 95 2 50 3/4 19
MB-1113(Single) 6 150 3 75 3-3/4 95 2-1/4 55 1 25


Magnetic Chucks


High power chucks
Solid top and bottom plates ensure retained accuracy
Full loading power over entire plate
Hand release with lathe chuck key provided
Standard pole and fine pole available

Cat No Size Angles
std.pole fine pole inch mm
MC-1114 MC-1121 5 125
MC-1115 MC-1122 6 150
MC-1116 MC-1123 7 175
MC-1117 MC-1124 8 200
MC-1118 MC-1125 9 225
MC-1119 MC-1126 10 250
MC-1120 MC-1127 12 300

Vices


Rotatry Tables


  • Horizontal and Vertical Rotary Tables with 360° graduations.
  • Features dual Positive action locks with extra deep coolant channel.
  • Table clamping surface are precision ground and cylindrical center bore concentric
  • Gear ratio is 90 : 1 and dial graduations give 10 second vernier reading.
Cat No. Tables Size
Inch mm
RT-1148 4 100
RT-1149 6 150
RT-1150 8 200
RT-1151 10 250


Heavy Duty Milling Machine Vice


  • Vise body of high tensile, closed grain Cast Iron.
  • Hardened and ground Jaw Plates.
  • Swivel base graduated 360° for horizontal indexing.
  • Totally enclosed acme screw.
  • Low base design for use on drilling, Milling and Shaping Machine

Cat No. Jaw Width Jaw Depth Jaw Opening
Inch mm Inch mm Inch mm
MV-1155 2 50 1-1/4 30 2 50
MV-1156 4 100 1-5/8 40 4 100
MV-1157 5 125 2-1/8 53 5 125
MV-1158 6 150 2-1/4 55 6 150
MV-1159 8 200 2-3/8 60 8 200


Pipe & Bench Vice (All Steel)


  • These Heavy duty Vises are manufactured from steel to withstand tough works.
  • Features a large Anvil work area and built in Pipe Jaws.
  • 360° Swivel base with double lockdowns.
  • Extra pair of soft Jaws provided for special clamping application.
Cat No. Jaw Width Jaw Opening Pipe Capacity
Inch mm Inch mm Inch mm
BV-1184 5 125 7 175 5/8 – 4 16 –100
BV-1185 8 200 10 250 5/8 – 6 16 –150


Grinding Vice Screw Type


Material En-31

Model Jaw width Jaw Depth Max Opening Overall Length Overall Height Parallelism Perpendicularity
KAP-SV1 60 30 60 160 60 0.01 Max 0.01 Max
KAP-SV2 75 40 80 205 70 0.01 Max 0.01 Max
KAP-SV3 100 45 105 240 90 0.01 Max 0.01 Max
 

Material M.S.

Model Jaw width Jaw Depth Max Opening Overall Length Overall Height Parallelism Perpendicularity
KAP-SV4 60 30 60 160 60 0.01 Max 0.01 Max
KAP-SV5 75 40 80 200 70 0.01 Max 0.015 Max
KAP-SV6 95 45 105 235 90 0.01 Max 0.015 Max


 
Home About us Our Products Contact us Send Enquiry
Copyright 2008, all Right Reserved Site Developed and Hosted by Trademart.in
Powered by LinXsmart Technologies